Last Updated on October 15, 2021 by PATRICIA LINDA
If you are a woodworker, then a table saw is a fundamental element of your work. A table saw is quite an expensive and necessary tool. So, you need to take care of the table saw. Your woodworking process would be perfect with a smooth table saw blade. If your table saw gets rust, then it will not perform properly. So, first, you should know how to clean or remove rust from your table saw blade? Because this rust is a great enemy for your table saw equipment that could damage it forever. The iron tabletop feature is the most valuable part of your table saw. This ironic blade of an expensive table saw gets rust early because dirty blades can cut poor smooth quality cuts in wood.
Therefore, this content will tell you some prevention to get rid of rust of ironic blade. And can do well in your work with the heavy and smooth table saw for a long time. First, you have to find out why and how to get rust from a table saw. Some little reason causes big trouble. Some common causes are-
- If a table saw serves a lot of work.
- Many years of use also happen to get the rust off.
- After working table saw did not clean a proper way.
- Sometimes water can have stuck in the table saw.
- If you did not work in these for many years.
- Lots of dust and oil can damage and rust your table saw.
Why does a table saw top site rust in early?
The top part of the table saw is most important for a woodworker. Many times woodworkers do cutting angles from any wood part in a table saw. So. rust attacks quickly after work. So need to clean the tabletop surface after working or cutting edges. A woodworker cannot work well without these top parts. This table saw the top part made of one or two-part great meatal. In this tabletop smallest and lightest are made of the Aluminum top. But cast metal is perfect for long-lasting. This cast metal is heavy mass but works well from aluminum metal. In the presence of moisture, iron undergoes a chemical reaction called oxidation. This process results in the decomposition of cast iron into iron oxide – the crusty, rusty substance we are familiar with as rust.
How to remove rust from a table saw?
Get rid of the rust:
First, need to arrange some element that can help you to remove rust easily. So, get safety equipment, pieces of clean cloth, rust remover spray, sandpaper, a metal brush, and nail jelly. Then you can wear gloves and remove to knock the rust with some scrappers. If needed, then do this work repeat to clean it thoroughly. It is most likely that the rust is stuck on its top because so much work occurs there. So, this rust removal process is not so hard to clean. Just remove the spot and rubbing the is to get a smooth part of the table saw portion.
A method based on nature:
To remove rust from saw edges, you can try the natural method. You can quickly get the necessary things. You can look for some natural remedies such as drinking coca-cola, baking soda, vinegar, baking soda, rust removing gel, sandpaper, and oxalic acid to remove rust early. Thing things are uses in many ways. Before discussing rust removers, it is vital to realize that you can get rid of table saw rust with some traditional, safe, and natural methods if you wish. Here I discuss easy and short timing two techniques that are available in our home or household shops.
Use lemon and salt to remove rust:
First, you arrange lemon and salt together to form a smooth paste. Cut the lemon and squeeze lemon water and mix with salt. Combine everything with your hands, get a paste, and rub it on the top of saw blades in rust. After spotting the mixture, let it for ½ hours. And after that, you can scrub with a clean cloth or brush. It will easily remove and clean. This lemon and salt method can save you time e and money. So, you can try and use this easiest method for that reason.
Use baking soda to get rid of rust:
Another method is using baking soda, readily available in any superstore shop. Wearing gloves or using a soft brush to protect your hands will be important when you make a paste by mixing baking soda and water. Put the baking soda paste on the top surface of the table saw. And wait until one hour to get clean surface blades. After an hour, you should gently rub the saw blades and clean them with water. Then you get your clean table saw blade.
However, you can use any quick and easy method to get a clean table saw blade without rust.
Try rust remover to get clean saw blades:
To get a quick result and not waste any time, you should use rust remover. Rust remover is easy to use better than natural methods or scrubbing. In a market or super shop place, there are so many rust removers for you. You can choose the better one that is suitable for your table saw surface. This table saw rust remover gives you a perfect and original look that looks like the first one. Here I discuss some rust remover that helps you to know about these details.
Empire top saver:
This Empire top saver is perfect for table saw, band saw, or any heavy saw rust remover process. It takes five minutes longer time for table saw surface treatment. This remover adjusts with some chemicals that are some lubricant, surface sealant, metal conditioner. It will never stain wood or interfere with glues or finishes. But it can remove rust, inhibit corrosion, repel dirt and moisture, which are the most important things to reduce rust. In a quick, you can spray this remover on the rusted surface and wipe it with a clean cloth or scouring pad or any light steel wool with a soft rub. Just for two cycles, it can easily remove from the table saw.
Boeshield rust-free remover:
Boeshield is a brand of rust remover that can spray and wipe nicely. Using this rust-free formula, you can clean bare metal surfaces, protect them from corrosion, and remove stains and rust from nearly any surface of the table saw. The rust removal formula works on steel, cast iron, fiberglass, chrome, tile, and porcelain. Guns and black oxide tools are undesirable for use. It is convenient to use on a table saw top surface. Spray on the stuck-in rust and wait for a minute after that, rub it with a Scotch-Brite pad or small steel tool followed by another wipe with clean clothes. Wait no longer than necessary, or some black spot will be visible on the surface that is not noticeable.
Clean the table saw surface perfectly:
whatever you use a natural method or rust remover to remove your table saw rust, you should clean perfectly in your table saw surroundings. You will get clean and long-lasting saw blades. So, try to use a lubricant to get smooth finishing. So, you can use automotive rubbing fluid and a buffing wheel. And rest time should use wax for polishing the table saw surface. That’s why you can use Johnson’s paste wax. This brand is popular with woodworkers and can do perform well in saw table polishing. This polishing should be applying nicely in 20 minutes later wipe that with clean clothes.
Protect yourself from injury:
Before you begin to do any work to remove or clean rust from a saw or table saw, make sure that you are in good health. Because in working time you might be injured from blade or saw. Table saw teeth very sharp and in removing rust already clean and sharpness more. So, in working time you can wear plastic clothes or PPE and wear hand gloves. You can wear rubber gloves or any protective gloves that can protect your hand from any injury. Also, you can protect your hands dry from any wax or liquid jelly that gets some chemicals or acids. To protect the eye, you can also wear glass. After wear protective things, you can easily do work in your place.
Here are some helpful topics that will help you in your work. Moreover, the fence and miter gauge make from metal and are susceptible to damage from the iron coat. Fortunately, you can clean the dust collector, fence, miter gauge in the same way as removing the table saw rust. And, do be cautious when using sandpaper and solid steel brush to avoid damaging the blade teeth. I wish this thing could help protect your table saw from corrosion during your working time.
Conclusion:
Once you remove table saw dirt, you can take a step back and admire the great results you have achieved. However, the topic of the above point is essential to follow to rid of rust from a table saw. If you are trying to avoid placing moisture-containing products on top of the table, it appears to be tricky; nonetheless, you can prevent moisture-containing objects from being placed on top of the table. In some cases, woodworkers cover the table of the saw with a smooth, solid layer of finish-grade plywood or MDF to protect future rust of the table saw. If you follow the amusing topic, you will have the ability to successfully remove the rust from the saw and maintain it for future use.
Leave a Reply